TY - THES U1 - Master Thesis A1 - Özkan, Nurullah T1 - Entwicklung eines Messkonzeptes zur Detektion ionisierender Photonenstrahlung durch ein elektronisches Personendosimeter N2 - Ionisierende Strahlung kann bei höheren Dosisleistungen lebensgefährlich sein. Um die Menschen vor solch einer Strahlung warnen zu können, wird im Rahmen dieser Arbeit die Entwicklung eines Messkonzeptes in CMOS Technologie zur Detektion ionisierender Photonenstrahlung durch ein elektronisches Personendosimeter beschrieben. Die entwickelte Schaltung soll später in einem Personendosimeter im klinischen Umfeld zum Einsatz kommen. Zusätzlich werden die Charakteristiken einer PIN-Diode untersucht. Die Schaltung wird auf Transistorebene aufgebaut, sodass sie später als integrierte Schaltung in einem Chip hergestellt werden kann. N2 - Development of a measurement concept for the detection ionizing photon radiation by means of an electronic personal dosimeter Ionizing radiation can be life-threatening at higher dose rates. In order to be able to warn people of such radiation, this thesis describes the development of a measurement concept in CMOS technology for the detection of ionizing photon radiation by an electronic personal dosimeter. The developed circuit will later be used in a personal dosimeter in a clinical environment. In addition, the characteristics of a PIN diode are investigated. The circuit will be built at the transistor level so that it can later be produced as an integrated circuit in a chip. KW - CMOS Y2 - 2022 UN - https://nbn-resolving.org/urn:nbn:de:hbz:dm13-31698 U6 - https://doi.org/10.26205/opus-3169 DO - https://doi.org/10.26205/opus-3169 SP - 147 S1 - 147 ER - TY - THES U1 - Master Thesis A1 - Zorn, Jendrik T1 - Messtechnische Validierung eines Shunt-Low-Dropout- Spannungsreglers zur strombasierten Versorgung der seriell verschalteten Pixel-Detektormodule des ATLAS- und CMS-Experiments am High-Luminosity Large Hadron Collider N2 - In dieser Masterthesis wird ein Shunt-Low-Dropout-Spannungsregler messtechnisch überprüft. Dieser Regler entsteht in Kooperation zwischen der Fachhochschule Dortmund und dem Kernforschungszentrum CERN für die Nutzung in Experimenten am LHC-Teilchenbeschleuniger in Genf. Der Fokus liegt auf der Messung der ersten beiden entwickelten Testchips des Projektes RD53B, inklusive der technischen Grundlagen, des genutzten Messaufbaus und der Validierung. Diese Thesis soll den Grundstein für Messungen an den folgenden Chipgenerationen im Rahmen des Projektes legen. Y2 - 2019 UN - https://nbn-resolving.org/urn:nbn:de:hbz:dm13-30541 U6 - https://doi.org/10.26205/opus-3054 DO - https://doi.org/10.26205/opus-3054 SP - 86 S1 - 86 ER - TY - THES U1 - Master Thesis A1 - Yilmaz, Semih T1 - Entwurf eines strahlenharten 5V Spannungsreglers aus kaskodierten Dünngate-Transistoren in einer 65nm CMOS Technologie N2 - Der vorliegende Bericht „Entwurf eines strahlenharten 5V Spannungsreglers aus kaskodierten Dünngate-Transistoren in einer 65nm CMOS Technologie“ beschreibt eine an der Fachhochschule Dortmund im Fachbereich Elektrotechnik im Rahmen der Masterthesis durchgeführte Studie. Ziel des Projekts ist die Entwicklung eines 5V Spannungsreglers, der einen CAN zu I2C Brücken Chip mit Spannung versorgt. Dabei ist zu beachten, dass die Core Transistoren in 65nm CMOS mit einer maximalen Spannung von 1,2V betrieben werden können. Der Chip soll für die Steuerung des Atlas Pixel Detektors am CERN eingesetzt werden. Y2 - 2019 UN - https://nbn-resolving.org/urn:nbn:de:hbz:dm13-30621 U6 - https://doi.org/10.26205/opus-3062 DO - https://doi.org/10.26205/opus-3062 SP - 71 S1 - 71 ER - TY - JOUR U1 - Zeitschriftenartikel, wissenschaftlich - begutachtet (reviewed) A1 - Woyczyk, Alexander A1 - Fleischhauer, Vincent A1 - Zaunseder, Sebastian T1 - Adaptive Gaussian mixture model driven level set segmentation for remote pulse rate detection JF - IEEE Journal of Biomedical and Health Informatics Y1 - 2021 SN - 2168-2194 SS - 2168-2194 VL - 25 (2021) IS - 5 SP - 1361 EP - 1372 ER - TY - THES U1 - Master Thesis A1 - Winkler, Florian T1 - Verification of the Shunt-Low-Dropout voltage regulator for the current based supply of the serially connected pixel detector modules of the ATLAS- and CMS-experiments at the High-Luminosity Large Hadron Collider N2 - Diese Ausarbeitung dokumentiert die Verifikation des Shunt-Low-Dropout-Spannungsreglers für den Einsatz im ATLAS- und CMS-Projekt. Im Rahmen einer Kooperation zwischen der Fachhochschule Dortmund und dem Forschungsinstitut CERN in Genf wird eine integrierte CMOS Schaltung zur seriellen, strombasierten Spannungsregelung der Pixeldetektormodule entwickelt. Der Fokus dieser Masterthesis ist die simulationstechnische Verifikation unter Berücksichtigung der spezifizierten Einsatzbedingungen in den Experimenten und umfasst - neben einer Einführung in den Shunt-LDO Regler auf Basis des Testchip C - die Vorstellung und Dokumentation der erarbeiteten Simulationsergebnisse. Y2 - 2019 UN - https://nbn-resolving.org/urn:nbn:de:hbz:dm13-30597 U6 - https://doi.org/10.26205/opus-3059 DO - https://doi.org/10.26205/opus-3059 SP - 71 S1 - 71 ER - TY - THES U1 - Master Thesis A1 - Walsemann, Alexander T1 - Entwicklung eines Testsystems für den Physical- und Data-Link-Layer des PSI5-Busses mit automatisierter Auswertung auf Basis der Xilinx ZYNQ SoCs N2 - Die vorliegende Masterthesis beschreibt die Entwicklung eines Testsystems für die PSI5- Schnittstelle von ASICs und ASSPs. Zunächst werden anhand des PSI5-Standards die Eigenschaften des Physical- und Data-Link-Layers aufgezeigt, welche neben etwaigen Störgrößen relevant für die Entwicklung des Testsystems sind. Das anschließend entwickelte Testsystem besteht aus einem physical Layer und einem ZYNQ SoC, welcher programmierbare Logik (FPGA) und CPU-Kerne vereint. Die Kernfunktionen der Sensorsimulation zum Testen eines PSI5-Master-Interfaces sind in programmierbarer Logik umgesetzt, während Softwareapplikationen für den Testablauf und die automatisierte Auswertung der Ergebnisse verantwortlich sind. Die beiden CPU-Kerne des ZYNQ SoCs werden als ein asymmetrisches Multiprozessorsystem aus dem Echtzeitbetriebssystem FreeRTOS für zeitkritische Aufgaben und einem modifizierten Linux-Kernel genutzt. Die Bedienung des Testsystems erfolgt über ein Webinterface. Y2 - 2019 UN - https://nbn-resolving.org/urn:nbn:de:hbz:dm13-30568 U6 - https://doi.org/10.26205/opus-3056 DO - https://doi.org/10.26205/opus-3056 SP - 168 S1 - 168 ER - TY - BOOK U1 - Buch A1 - Urban, Gerald A. A1 - Becker, Kurt A1 - Braecklein, Martin A1 - Habenstein, Birgit A1 - Knaup, Petra A1 - Melzer, Andreas A1 - Stieglitz, Thomas A1 - Urban, Gerald A1 - Zaunseder, Sebastian T1 - Technologische Souveränität in der Biomedizinischen Technik - der Mensch im Fokus BT - VDE-Positionspapier Y1 - 2021 SP - 52 S1 - 52 PB - VDE Verband der Elektrotechnik Elektronik Informationstechnik CY - Frankfurt am Main ER - TY - THES U1 - Master Thesis A1 - Shi, Yanchen T1 - Power Simulation of a MIPS microAptiv UP Core implemented as a virtual ASIC prototype in a 65nm CMOS technology N2 - This thesis presents a power simulation of a MIPS MicroAptiv UP Core implemented as a virtual ASIC prototype using Taiwan Semiconductor Manufacturing Company(TSMC) 65 nm CMOS technology. Based on the MIPS instruction set program data is generated and introduced in the simulation by means of initialization files. Before the simulation, technology specific SRAM modules are integrated into theMIPS core. Two different programs are used for power characterization. The first program performs frequent memory accesses by means of load/store word instructions, while the second program is a loop which operates on registers only and mainly increments addresses. The simulation is based on a virtual prototype which is generated by synthesis and place & route including post-layout parasitic extractions. The stimuli for the power extraction is generated via gate-level simulation and forwarded to the power calculation engine. The effect of X-propagation on gate-level simulations is avoided by modifying the address-related statements in the execution data path module, which use another form of 2 to 1 multiplexer, setting the output to zero for all input signals even with an initial value of ’x’ without changing the functionality. Finally, the consumed power is provided by reports generated by the power simulation engine. The memory-centric program consumes 35.39mW of internal power using instructions, which is 0.73mW less than the internal power of the register-centric program, and the overall average power is also lower by almost 0.7mW. Y2 - 2022 UN - https://nbn-resolving.org/urn:nbn:de:hbz:dm13-32171 U6 - https://doi.org/10.26205/opus-3217 DO - https://doi.org/10.26205/opus-3217 SP - 93 S1 - 93 ER - TY - BOOK U1 - Buch A1 - Scholz, Reinhard T1 - Grundlagen der Elektrotechnik BT - Eine Einführung in die Gleich- und Wechselstromtechnik Y1 - 2018 SN - 978-3-446-45160-5 SB - 978-3-446-45160-5 SP - 249 S1 - 249 PB - Fachbuchverlag Leipzig im Carl Hanser Verlag CY - München ER - TY - THES U1 - Master Thesis A1 - Rizwan, Ahmad T1 - Analog and Digital CMOS Circuit Design for the Control System of ATLAS Pixel Detector N2 - This Master thesis is part of an effort to implement the planned upgrade High- Luminosity Large Hadron Collider (HL-LHC) at CERN Geneva/Switzerland. The ATLAS Pixel Detector which is installed at the LHC is also getting among others a new detector control system (DCS) update. Each module in the Detector Control System will have an integrated DCS chip which includes on-chip shunt and Linear regulators, ADC, bypass transistor and a modified I2C slave node. In this master thesis, Shunt and Linear regulators are explained and simulated using the Globalfoundaries 130nm CMOS designkit. A Kuijk bandgap reference based Power-On-Reset (POR) circuit is explained and designed in detail. The design of the POR includes an implementation with CMOS instead of diodes or bipolar transistors. It was simulated using Globelfoundaries 130nm CMOS designkit. Finally, a layout was developed for fabrication. The DCS system needs DCS bridge controllers which include a Controller Area Network (CAN) node and a modified I2C master node. For this purpose CAN and CANopen standards are explained in detail for implementation. Y2 - 2018 UN - https://nbn-resolving.org/urn:nbn:de:hbz:dm13-30554 U6 - https://doi.org/10.26205/opus-3055 DO - https://doi.org/10.26205/opus-3055 SP - 114 S1 - 114 ER -